Andis UltraEdge Clipper Blade Size 5FC

Andis® UltraEdge™ Clipper Blades are made from carbon-infused steel for a harder cutting surface that lasts longer. This size 5 FC dog clipper blade has a 1/4" cut (6.3 mm). Leaves a smooth, short finish.

Item #AD64122

ONLY
$19.05

Andis® UltraEdge™ Clipper Blades are made from high-carbon steel and processed through a unique carburizing heat treatment that actually adds carbon to the existing metal producing a harder cutting surface. Andis clipper blades hold a razor sharp edge that will endure prolonged use and more sharpening treatments.

The Size 5FC Finish Blade:

Has a 1/4" blade cut, most often used for a smooth, short lamb finish
Is effective for finishing the coat after trimming with a #5 skip tooth blade
Leaves a nice finished length on the coats of wire, welsh, and Lakeland terriers

Each Andis UltraEdge blade is sharpened to exact quality standards and is hand-tested before it is shipped. Blades have a Rockwell Hardness rating of 65.

Compatible with Andis®, Conair®, Oster®, and Wahl® detachable-style clippers.

Not sure what blade size you need? View our clipper blade sizing chart

See the Specifications and Instructions tabs for more product details.

Material: Carbon-infused steel
Cut: 1/4" (6.3 mm)
Rockwell Hardness Rating: 65

Andis UltraEdge Clipper Blades are available in the following styles:

Size 50 Blade has a 1/125" Blade Cut
Size 40 Blade has a 1/100" Blade Cut
Size 30 Blade has a 1/50" Blade Cut
Size 5/8 Toe Blade has a 1/32" Blade Cut
Size 15 Blade has a 3/64" Blade Cut
Size 10 Blade has a 1/16" Blade Cut
Size 9 Blade has a 5/64" Blade Cut
Size 8 1/2" Blade has a 7/64" Blade Cut
Size 7 Skip Tooth Blade has a 1/8" Blade Cut
Size 7F Finish Blade has a 1/8" Blade Cut
Size 5 Skip Tooth Blade has a 1/4" Blade Cut
Size 5F Finish Blade has a 1/4" Blade Cut
Size 4 Skip Tooth Blade has a 3/8" Blade Cut
Size 4 Finish Blade has a 3/8" Blade Cut
Size 3 3/4" Skip Tooth Blade has a 1/2" Blade Cut
Size 5/8 HT Blade has a 5/8" Blade Cut

See the Instructions tab for more product information.

Blade sets should be oiled once a day minimum! Ideally, it should be done before every grooming. After oiling, be sure to use a soft, dry cloth to wipe any oil off the external surfaces to reduce the possibility of getting it on the animal’s coat. If the clipper blades leave streaks or slow down, it’s a sure sign that the blades need oil.

Oiling Blades: Place a few drops of blade oil on the front and side of the cutter blades. Wipe excess oil off blades with a soft, dry cloth. Spray lubricants contain insufficient oil for good lubrication, but are an excellent clipper blade coolant.

Cleaning Blades: Immerse blades only while clipper is running in a shallow pan of clipper oil or blade cleaner. After cleaning, turn the clipper off and dry blades with a clean, dry cloth. If blades will still not cut, there may still be some hair trapped between the upper and lower blade. Remove the blade off the clipper and slide the upper blade to one side without loosening the tension spring or moving the upper blade completely out from under the tension spring. Wipe the surfaces of the blades clean with a dry cloth, then place a drop of clipper oil where the upper and lower blades meet and also in the guide slot of the tension spring.

Always replace broken or nicked blades to prevent injury.