Just add cold water to the Cool Bed III™
keep dogs cool both indoors and out. Once saturated with water,
the foam inner core provides a cool, refreshing surface for
your dog in when warm weather hits.
- Cool core is easy on pet joints and brings relief to
painful medical conditions
- Outer shell is made of extremely durable nylon
- Valves make it easy to expel unwanted air and fluid while
filling or draining
- Non-toxic and no chemicals or electricity required
Material: Outer shell is made of extremely
Small measures 24"L x 17"W and holds pets up to
Medium measures 32 "L x 22"W and holds pets up to
Large measures 44"L x 32"W and holds pets over 60
Please read all precautions and instructions before use. The
Cool Bed III should provide years of soft, cool, gel-like
sleeping comfort for your dog. Please read all instructions
before using this product.
Directions For Use
How to empty your Cool Bed III
- Step 1. Remove the Cool Bed III from the box. Locate the
filler cap on the bed and open it by grasping the base of the
cap with one hand and the tab of the cap with the other. Pull
the cap open. Flatten the Cool Bed III and let it sit for a
few minutes to allow the cool core interior to retain its
shape as all air has been removed for shipping.
- Step 2. Place the Cool Bed III in the intended location
with the cap side of the bed up for filling. Place a towel
under the filler cap end of the bed to absorb any
accidentally spilled water. Using a calibrated container with
a pour spout, begin carefully filling the Cool Bed III with
- The bed will take the following water quantities.
Keep in mind, the more water used, the more cushioning
and cooling capabilities the bed will have. You can
experiment for the optimal feel of the Cool Bed III.
Ultimately the recommended quantity of water for best
cooling capabilities is as follows:
Small Cool Bed III: 1.85 gallons
Medium Cool Bed III: 3.25 gallons
Large Cool Bed III: 6.75 gallons
- The water in the Cool Bed III should be around
15%-20% deeper than the Cool Core. What this means is
that the Cool Bed III empty is around 1 inch thick. After
filling and expelling the air, the bed should be a
minimum of 1 3/16 inches thick. This extra water
circulating through the Cool Core’s channels will provide
incredible cooling power.
- Step 3. Now that you have your Cool Bed III filled, close
the filler cap and begin to knead the bed to help work the
water into the Cool Core. Now pull open the air adjustment
valve and gently work as much air out as you can, using
sweeping motions across the Cool Bed III with your hands.
Sweep the air towards the valve allowing the air to expel
from the bed. Seal the valve when most of the air has been
removed. You will feel how comfortable the bed will be at
this point. The bed should feel very soft and spongy and you
should feel water squishing around inside the bed. Now decide
if a little more water is desirable or if it's just right for
your pet. Add water if necessary, repeating the air removal
Note: A little air inside the bed will not affect
the cooling capabilities of the Cool Bed III. If you choose,
you may expel air as needed though not necessary.
- Step 4. Your bed is now ready to be turned over and used
by your pet. To turn the bed over, grasp the edges of the bed
with both hands and roll the bed over. Be careful as the bed
may be heavy. You may then grasp the edges of the bed to
slide it on the floor for exact positioning.
How Does the Cool Bed III™ work?
- Open the filler cap.
- Roll bed from opposite end, expelling water out of the
cap. (much like rolling a sleeping bag)
- Store with filler cap open.
Unlike a fluffy dog bed that is designed to retain heat to
keep a dog warm, the Cool Bed III is designed to radiate heat
back into the air or the floor surface to keep a dog cool. The
water-saturated Cool Core™ inside the Cool Bed III absorbs the
dog’s natural body temperature of 102° Fahrenheit and coverts
it to room temperature, which is normally well below the dog’s
body temperature. The difference created between the room
temperature and the dog’s body temperature is how the Cool Bed
III provides a cooler, refreshing surface for your dog. Even if
it is 80°F in your house, the Cool Bed III is 22° cooler than a
dog’s 102° body temperature.
The Cool Bed III provides a permanent, natural, cool spot for
your dog, inside or outside in temperatures under 95°
Fahrenheit without chemicals or electricity.
- Have your dog’s nails routinely trimmed to prevent
- Cool Bed should be placed on a smooth surface that cannot
cause punctures, abrasions or leakage.
- Routinely check under your Cool Bed III for
- The surface can be cleaned using a damp towel or sponge
and mild dishwashing detergent. Do not wash in a washing
- Never use the Cool Bed III in direct sunlight. Always
place in shade, as direct sun will warm the Cool Bed
- Always place the Cool Bed III out of the way of foot
- Never allow the Cool Bed III to freeze.
- Cool Bed III is not intended to be a life saving
- This product is to be used in temperatures under 95°
How to use your new Cool Bed III™
The best results will be obtained when used in a shady area.
When using outdoors, always place the Cool Bed III in a shady,
cool spot, as this will maximize its heat wicking abilities. Be
sure not to place the bed on sharp objects that could puncture
the Cool Bed III. Keeping the Cool Bed III indoors overnight
near air conditioning will super cool the bed for outdoor use
the next morning. When using indoors, be sure to place the Cool
Bed III out of direct sunlight. The cooler the spot you place
the Cool Bed III, the better. An ideal place would be a cool
tile, linoleum or concrete floor. An area with good air
movement will also help keep the bed cooler. You will soon
figure out the best location for your new Cool Bed III, and
your pet will love you for it!
Shipping Info: This item is not eligible
for free or discounted shipping. This item ships directly from
the manufacturer. Please allow 1-2 weeks for delivery.